First estimations of the aerosol optical thickness using Langley Method at Southern Brazil (29.4°S, 53.8°W)

The first estimations of the aerosol optical thickness (AOT) using Langley Method at Southern Space Observatory (SSO) at Southern Brazil (29.4°S, 53.8°W) are presented. In addition to ozone and sulphur dioxide columns, AOT can be obtained using Brewer Spectrophotometer at specific wavelengths: 306.3, 310.1, 313.5, 316.8 and 320.1 nm. The AOT was obtained for the period from November/2002 to May/2003. Very low AOT averages were obtained, whose values were about 0.21 ± 0.03 at 306.3 nm, 0.21 ± 0.02 at 310.1 nm, 0.19 ± 0.02 at 313.5 nm, 0.20 ± 0.02 at 316.8 nm and 0.20 ± 0.02 at 320.0 nm for all period analysed. Different behaviour of AOT were obtained at two daily specific periods of aerosol accumulation, one in the afternoons from November/2002 to February/2003, caused mainly by a mild biomass burning season’s in the region and other in the mornings from March to May/2003, due the high relative humidity presented in the region studied.     

射线检测厚度宽容度的分析与测定

厚度宽容度是变截面工件射线检测的重要参数。本文分析了典型工件的厚度差,以及不同灵敏度级别的厚度宽容度。应用胶片特性曲线、曝光曲线,从实验角度测量了厚度宽容度,并对结果作了分析和讨论。     

蓄冰盘管冰层厚度测量及管外蓄冰性能实验

提出了一种新型简便的冰层厚度测量方法,该方法用测量冰层内温度分布的方法间接测量冰层动态厚度及冰层的相界面生长规律。对蓄冰盘管外结冰过程的实验研究表明,测量方法可靠,具有较高的测量精度;实验发现,蓄冰盘管外上部冰层生长较快,而下部冰层生长较慢,而在实验参数范围内管内乙二醇水溶液流量对冰层生长速度影响不大。     

Microstructure and Optical Characterization of Magnetron Sputtered NbN Thin Films

Some fundamental studies on the preparation, structure and optical properties of NbN films were carried out. NbN thin films were deposited by DC reactive magnetron sputtering at different N2 partial pressures and different substrate temperatures ranging from –50 ℃ to 600 ℃. X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM) were employed to characterize their phase com- ponents, microstructures, grain sizes and surface morphology. Optical properties inclusive of refractive indexes, extinction coefficients and transmittance of the NbN films under different sputtering conditions were measured. With the increase in the N2 partial pressure, δ-NbN phase structure gets forming and the grain size and lattice constant of the cubic NbN increasing. The deposited NbN film has relatively high values of refractive index and extinction coefficient in the wavelength ranging from 240 nm to 830 nm. Substrate tem- perature exerts notable influences on the microstructure and optical transmittance of the NbN films. The grain sizes of the δ-NbN film remarkably increase with the rise of the substrate temperature, while the transmittance of the films with the same thickness decreases. Ultra-fine granular film with particle size of several nanometers forms when the substrate is cooled to –50 ℃, and a remarkable aug- mentation of transmittance could be noticed under so low a temperature.     

变厚度锥形壳的固有频率

 变厚度锥形壳体的固有频率使用有限元计算已无困难,但有限元法编制程序复杂、费时多。本文用半解析法,由锥形壳的基本方程导出等价的8个一阶微分方程,用数值积分方法得到变厚度锥形壳体的固有频率。方法简单,编程容易,计算精度已满足工程计算要求。     

零件纵向厚度的计算方法

在用车床加工空心旋转体零件时，通过测量我们可以得出外轮廓曲线，但根据零件的设计技术要求，不同点处的法向厚度不同，因此在用车床加工时需要计算出各点的纵向厚度。本文给出了根据法向厚度及外曲线计算纵向厚度的方法．该方法简单、可靠，易于计算，而且由此方法计算的结果应用到实际加工时，效果非常好，该方法实用性强，易于推广使用。     

磁控溅射沉积工艺条件对薄膜厚度均匀性的影响

薄膜厚度均匀性是衡量薄膜质量和镀膜装置性能的一项重要指标.在自行设计的磁控溅射沉积设备上,对薄膜沉积工艺中靶基间距、溅射功率、工作气压对膜厚均匀性的影响进行了研究,由连续光谱椭圆偏光仪SE800测量薄膜厚度.结果表明:靶基间距较大的情况下,薄膜均匀性明显改善;溅射功率和工作气压对薄膜均匀性也有较大的影响.     

浅谈飞机螺纹连接件电镀层厚度及螺纹配合间隙

在沿海地区服役的飞机 ,通常是在含有腐蚀性气体和在高温及高湿热复杂环境条件下工作的。此时 ,暴露在外部及内部需经常拆卸的飞机螺纹连接件的锈蚀问题 ,严重地影响了飞机连接件的正常拆卸和安装及连接件的寿命。为提高飞机螺纹连接件的抗腐蚀能力 ,改善飞机的维修性能和提高飞机的使用寿命 ,本文根据镀层厚度与螺纹配合间隙的关系 ,结合国内外相应标准的规定 ,在保证螺纹连接强度的情况下 ,对如何合理选择镀层厚度和螺纹配合间隙来提高抗腐蚀能力的问题做了论述     

切向结构永磁同步电机中磁钢厚度对性能的影响

提出了切向结构永磁同步电机中磁钢厚度的约束条件;依据电机学理论并结合有限元计算方法,研究了气隙长度恒定时不同极对数下气隙磁密、每极磁通与磁钢厚度的关系,探讨了磁钢厚度对电机的过载能力、铁耗等性能的影响;在气隙长度发生变化时,为了保证漏磁大小不变,讨论了气隙与非导磁衬套厚度、磁钢厚度的关系。并指出:(1)气隙恒定时,随着磁钢厚度的增加,不同极对数时磁钢体积增大所提供的磁势对每极磁通的影响有所不同;铁耗和过载能力随磁钢厚度的增加而增大。(2)气隙增大时,为了保证气隙磁密和漏磁不变,必须增加非导磁衬套的厚度。(3)极对数增加时,减小磁钢厚度能提高电机的性价比。     

大厚度比零件（外侧）和波纹管（内侧）的缝焊研究

某重点型号波纹管组合件的设计要求是缝焊，对照以往产品的结构，比较明显的情况是波纹管在零件的内侧。零件的厚度是3mm，波纹管的厚度是0.1mm，零件与波纹管的厚度比比较大。波纹管在零件的内侧会产生一个问题：波纹管在焊接过程中会逐渐收缩，到最后与零件之间产生间隙，导致局部形不成焊缝。研究通过减小车配间隙,增加冷却手段、滚轮厚度和压力等措施来实现大厚度比的零件和波纹管之间的缝焊。